Airlive wl-5460ap v2 user manual

It does not require a RADIUS server in order to provide association authentication, but you do have to enter a shared key for the authentication purpose. The encryption key is generated automatically and dynamically. Please make sure that both the WLAP and the wireless client stations use the same key. The shorter the interval is, the better the security is. The default is sec. All devices try to access the network should have the matching encryption key.

It is more secure than WEP encryption. Pre-authentication provides a way to establish a PMK security association before a client associates. The default is If your The value can be set from to The default value is Therefore, they are hidden nodes for each other.

When a station starts data transmission with the Access Point, it might not notice that the other station is already using the wireless medium. When these two stations send data at the same time, they might collide when arriving simultaneously at the Access Point. The collision will most certainly result in a loss of messages for both stations.

Thus, the RTS Threshold mechanism provides a solution to prevent data collisions. It will also confirm the requestor station that the Access Point has reserved it for the time-frame of the requested transmission. The RTS mechanism will be activated if the data size exceeds the value you set.. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy.

This value should remain at its default setting of Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval: Beacon Interval is the amount of time between beacon transmissions.

Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point. Data Rate: By default, the unit adaptively selects the highest possible rate for transmission. Select the basic rates to be used among the following options: Auto, 1, 2, 5. For most networks the default setting is Auto which is the best choice. When Auto is enabled the transmission rate will select the optimal rate.

If obstacles or interference are present, the system will automatically fall back to a lower rate. Preamble Type: A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. The Short Preamble is intended for applications where minimum overhead and maximum performance is desired. Enable WatchDog: Check and enable this watch dog function. Watch Interval: Setup the interval time for watch dog function between 1 to 60 mins.

Watch Host: Enter the watch dog host ip address. Ack timeout: When a packet is sent out from one wireless station to the other, it will waits for an Acknowledgement frame from the remote station. If the ACK is NOT received within that timeout period then the packet will be re-transmitted resulting in reduced throughput. By having the ability to adjust the ACK setting we can effectively optimize the throughput over long distance links.

This is especially true for If the list contains no entries with this function being enabled, then no clients will be able to access this Access Point. What type of Traffic Bandwidth Control does the E11 firmware offer? Therefore, all traffics are controlled the same way. So WISP can control the maximum data rate. What is the Output Rate?

This section is to configure the bandwidth by IP address. You can control more than one IP address. This section is to configure the bandwidth by MAC address. You can control more than one MAC address. You should perform the following steps: 1.

Reboot the AP. Define Policy A policy is a set of bandwidth rules that can be used as a template. Please follow the procedure below to setup IP Traffic Control 1.

Before you start, please check the following area to see which client IPs are supported. It differs between each mode. Please check this part to find out what IP addresses are supported. It varies between each mode. You cannot change the Out Rates if you have chosen a Policy If you want to define new Data Rate, please do not choose any policies. Before you start, please check the following area to see which client MACs are supported.

If you have defined a Policy already, please choose a Policy name. In this example, the AP is installed outdoor to provide Internet service.

System Management 4. If your system manager assigned you static IP settings, then you will have to enter the information provided. Subnet Mask: Enter the information provided by your system manager. Default Gateway: Enter the information provided by your system manager.

To Upgrade Firmware: 1. Download the latest firmware from your distributor and save the file on the hard drive. Click Reset to clear all the settings on this page. Or click Upload to start the upgrade. This function enables users to save the current configurations as a file i.

Or click Browse… to select the file. Leaving the user name and password blank will disable the protection. The login screen prompts immediately once you finish setting the account and password.

Remember your user name and password for you will be asked to enter them every time you access the web server of this Access Point.

New Password: Set your new password. Password can be up to 30 characters long. Password can contain letter, number and space. It is case sensitive. Confirm Password: Re-enter the new password for confirmation. Enable Log: Enabled or Disabled display system log information. System All: List system all log information.

Wireless Only List: wireless log information only. Refresh: Refresh log information. Clear: Clear all information in window. Time Zone Select: Select system time zone. If it is, it has emergency code function. Once you make sure it has emergency code function. Please follow the steps below: 1. Unplug the power of WLAP.

Hold the reset button while plugging the power. You should see the emergency code page where you can upload your AirLive firmware again. It needs to update bootloader first. To upload the bootloader and firmware: 1. Open the internet protocol setup dialog and enter IP addresses as shown below:. WLAP will then reboot itself. WLAP v2 Slovensky A OvisLink Corp. Para mais detalhes consulte por favor o manual de utilizador. Az OvisLink Corp. WLAP v2 Magyar Magyar WLAP v OvisLink S.

Italiano WLAP v Per altri dettagli, rivolgersi al manuale dell'utente. Per altri dettagli, vedere il manuale dell'utente. Per altri dettagli, vedere il Manuale dell'Utente. Renombrar el marcador. Eliminar marcador? Eliminar de mis manuales? Entrar O. Cargar el manual.